THE MARROW JOURNAL · Temperature & timing
Where to Put a Meat Thermometer in Steak: Thick, Thin and Bone-In Cuts
A thermometer is only useful when its sensing area reaches the part of the steak that heats last. For most steaks, that means the center of the thickest muscle, away from bone, large fat seams and gristle. Thick steaks can be checked from the top or side; thin steaks are usually easier to check from the side; bone-in and irregular steaks need readings in more than one place.
Thermometer placement by steak shape
USDA FSIS gives the governing rule: place the thermometer in the thickest part of the food and keep it away from bone, fat and gristle. The Beef Checkoff adds a steak-specific method for cuts at least 1/2 inch thick: insert an instant-read thermometer horizontally from the side so it reaches the center of the thickest part without touching bone or fat.
The table applies that rule to common steak shapes. It does not replace the thermometer manufacturer’s instructions, because different instruments measure temperature over different portions of their probes.
| Steak | Where the probe should enter | Where the sensing tip should finish | Extra check |
|---|---|---|---|
| Thick, boneless steak | From the side or top | Coolest point in the center of the thickest section | Scan past the center and back; check a second spot if thickness varies |
| Thin steak or cutlet | Horizontally from the side, or at a shallow angle | Center of the meat, with the thermometer’s full sensing area covered | Use a thin-tip thermocouple or another model approved for thin foods |
| Bone-in ribeye or strip | Into the thickest meat from a direction that avoids the bone | Center of the muscle, clear of bone and large fat seams | Repeat in another thick area |
| T-bone or porterhouse | Check each side separately | Center of both the strip and tenderloin muscles | Use the lower safe reading; the smaller tenderloin may heat differently |
| Irregular steak or roast-like cut | Into each substantial thick section | Center of each section | Do not assume one reading represents the whole piece |
Sources: USDA Food Safety and Inspection Service — How to use a food thermometer · Beef Checkoff — Determining Doneness and steak probe placement (industry source) · USDA Food Safety and Inspection Service — Thermocouple thermometers and thin foods
Know which part of the probe takes the reading
USDA FSIS describes thermocouple thermometers as fast instruments with thin probes that can measure thin foods near the end of cooking. Other stem thermometers may average temperature across a longer sensing zone and need deeper insertion. Read the model’s manual and use a sensor that can remain fully inside the steak.
For an instant-read tip sensor, ThermoWorks recommends moving the tip through the steak and watching the temperature change. Use the lowest stable center reading, not the first number near the hot surface.
Sources: USDA Food Safety and Inspection Service — Thermocouple thermometers and thin foods · USDA Food Safety and Inspection Service — Liquid-filled thermometers and insertion depth · ThermoWorks — Getting an Accurate Temperature Reading (commercial source)
How to scan a thick boneless steak
The geometric midpoint is not always the coolest point. Uneven thickness and recent flipping can move the thermal center, so scan instead of stopping at a guessed depth. Keep the probe off the pan or grate; for a side reading, lift the steak with clean tongs just long enough to insert the probe.
- Find the thickest continuous section rather than the fattest-looking edge.
- Insert the probe from the side when that gives a clearer path to the midline, or from the top when the steak is thick enough to control depth.
- Push the sensing tip slightly beyond the estimated center, then withdraw it slowly while watching the display.
- Use the lowest stable reading as the center temperature.
- Move to a second location when the steak has a tapered end, uneven thickness or a large internal fat seam.
Sources: USDA Food Safety and Inspection Service — How to use a food thermometer · ThermoWorks — How to Temp a Steak and find the thermal center (commercial source) · ThermoWorks — Getting an Accurate Temperature Reading (commercial source)
How to measure a thin steak
A top-down insertion can pass through the center into hot air or the cooking surface. Slide a thin probe horizontally through the side, or use a shallow angle, so its sensing area stays inside the meat. USDA FSIS identifies thermocouples as suitable for thin foods. Check another point when the cut is uneven.
Sources: USDA Food Safety and Inspection Service — Thermocouple thermometers and thin foods · Beef Checkoff — Determining Doneness and steak probe placement (industry source)
How to check bone-in and two-muscle steaks
USDA guidance says to avoid bone, fat and gristle. On a bone-in ribeye or strip, angle the probe into the thickest meat with clearance from the bone. If the probe meets hard resistance, withdraw and choose a new path.
A porterhouse or T-bone has strip and tenderloin muscles separated by bone. Check the center of both without touching the bone, and use the lower reading when confirming that the steak has reached a safe temperature.
Sources: USDA Food Safety and Inspection Service — How to use a food thermometer
Placement and the safety endpoint work together
USDA FSIS says raw beef steaks must reach a minimum internal temperature of 145°F before they are removed from the heat source, followed by a rest of at least three minutes. The rest is part of the safety instruction; it is not a substitute for reaching 145°F while the steak is still on the heat.
Carryover cooking varies, so do not remove a steak below the USDA minimum based on an estimated rise. Check each distinct thick section, clean the thermometer according to its instructions and rest the steak before carving or eating.
Sources: USDA Food Safety and Inspection Service — Safe internal temperatures for meat and poultry
Five placement mistakes to avoid
- Reading near the seared surface and treating that hotter number as the center.
- Stopping the probe against bone or inside a wide fat seam.
- Using a long-sensing-area dial thermometer in a steak too thin to cover that area.
- Checking only the strip side of a T-bone or only the thick end of an irregular steak.
- Trusting color, firmness or elapsed minutes instead of confirming the coolest center with a food thermometer.
Sources & further reading
Sources checked for this guide on November 16, 2026. Recommendations combine the cited information with Marrow’s practical editorial guidance.
- USDA Food Safety and Inspection Service — How to use a food thermometer
- USDA Food Safety and Inspection Service — Safe internal temperatures for meat and poultry
- USDA Food Safety and Inspection Service — Thermocouple thermometers and thin foods
- USDA Food Safety and Inspection Service — Liquid-filled thermometers and insertion depth
- Beef Checkoff — Determining Doneness and steak probe placement (industry source)
- ThermoWorks — How to Temp a Steak and find the thermal center (commercial source)
- ThermoWorks — Getting an Accurate Temperature Reading (commercial source)